Press Release

Screwdriving Technology

(Press Release, July 2014)

FlowForm Screwdriving - Trendspot at the AUTOMATICA 2014

Joining sheet metal directly, quickly and simply

Innovative screwdriving system for vehicle bodywork production

Whereas in the past, steel sheets were easy to join by spot welding or resistance welding, today this is no longer economical due to the modern material mix. The automobile industry is under pressure from legal requirements to reduce CO2 emissions, use lightweight design and consequently to find alternative joining methods. Where access to both sides of the connection point is available this can be done using rivets. If however only one side is accessible then the well-established direct screwdriving flow form principle comes into use. A flow form screw is positioned on an aluminium or steel sheet without pre-drilled holes and the screwdriving process begins. The screw is applied with a high pressure down-force and rotates at high speed, generating a frictional heat which forms a crater through which the screw’s thread passes under reduced pressure. A machined thread is created, a normal screw can also pass through in the case of repairs. After the flow passage has been formed the speed is reduced and the screw is tightened to the head connecting surface and then the final tightening of the fastener to the pre-determined parameters of torque and angle takes place. The entire procedure usually takes less than two seconds. Additional fastening elements such as nut and bolts are not required as the assembly has been optimally adjusted to the passage and thread of the screw. The screw is fixed. There is no need for preparatory drilling or punching of the component.

The screwdriving specialists DEPRAG SCHULZ GMBH u. CO. presented a live show on the topic of flow form screwdriving (FFS) at this year’s AUTOMATICA from the 3rd to the 6th of June in Munich under the slogan “Sheet Metal - Direct - Screw Assembly”. In Hall A6, exhibition stand 310 development, product and processing engineers from vehicle bodywork design departments, but also from many other braches in which sheet metal is assembled such as white goods, can gain first hand information about the next generation of FFS.  

What is new?

The DEPRAG engineers have successfully developed a freely programmable gear for a torque range of up to 15 Nm and speed range of up to 8000 rpm from two gears with 15 Nm at 6000 rpm and 12 Nm at 8000 rpm. As well as reduced investment costs, this also means a reduction in processing costs as replacement expenses do not apply.
The currently established FFS units usually shoot the flow drill screws tip first through the mouthpiece. Damage to the screw tip geometry is inevitable and can have devastating consequences. The required frictional heat which is necessary to penetrate the material cannot be generated. It is different in the new innovative DEPRAG flow form screwdriving unit: here the screw is shot in head first and an integrated revolver separator positions the screw so that its position is secured even for overhead assemblies. The next screw is reloaded already as the first screw is being seated. A decisive benefit in optimising the cycle time!

In developing this new generation further, years of operating experience have been incorporated. Jürgen Hierold, Sales Manager at DEPRAG explains, “Due to the complex geometry of bodywork the highest requirements for mobility of robots and the FFS unit are set. Combined rotation and pivoting movements of the robots are required in order to reach the screw assembly positions. Often the feedhose used can bend or twist so that the screws get stuck during loading. Massive disruptions to the assembly process, high risk to the processing reliability of the complete system and extensive fault clearance are the inevitable consequences. Therefore we were approached by one of the  largest internationally active companies in the automobile industry with the demand for a system which presented screws without a feedhose. We have developed a magazine system for our customer which is based on three basic elements, the screw magazine, the magazine exchange station and the screw feeder”. Whilst one magazine is in operation, docked on the FFS unit systematically presenting 32 fasteners, the second magazine is being filled at the exchange station by the screw feeder. The screw feeder is outside the activity range of the robot, refilling screws without interference in the danger zone. If the first magazine is empty then a robot on the exchange station removes it to be refilled and replaces it with an already filled magazine so that assembly may continue. Thereby the best possible processing times are achieved with guaranteed processing reliability. “We now have this exchange magazine available as a standard solution. Even existing FFS systems can be simply and easily upgraded to include it”, explains Jürgen Hierold.

Another aim of the developers for the new generation of FFS systems was the parameterisation of the screwdriving procedure for the operator so that it is as intuitive and simple as possible to use. System adjustment is automatic. The operator must only enter the screw geometry (shaft diameter and length), information relevant to the part (quantity, material and strength of the sheet, with/without drill hole) and the tightening parameters onto the clear HMI panel. Of course each screw assembly is individually analysed and displayed. Additionally the software provides comprehensive documentation and archiving options not only for individual screw assemblies but also for different sets of parameters.

Another plus point is the mouthpiece exchange device for the application. The adjustment to a different screw type or fault clearance is taken care of at the touch of a button. The lock is loosened and the mouthpiece can simply be exchanged.

Usually the holding function of the nosepieces is based on spring-loaded pressure. The disadvantage here is that the screws open the jaws against spring pressure and mechanical load through friction can occur. This is not the case on the new DEPRAG flow form unit, here the cylinder controlled nosepieces control the release of the screws as soon as the screw begins to form the passage, therefore friction between the screw head and nosepiece is greatly reduced.

“There are a number of advantages as a result of the improvements to the FFS unit: as well as the increased user friendliness, reduction of maintenance, varied user options and simplified system integration, above all the processing reliability of the flow form procedure has been decisively increased”, concludes Jürgen Hierold. Under the slogan “Sheet Metal - Direct - Screw Assembly” visitors can experience each of these improvements on the demo unit. DEPRAG is exhibiting the complete flow form process on their stand using various material pairings.

DEPRAG SCHULZ GMBH u. CO. employs 600 staff in over 50 countries and is based in Amberg, Germany. They have made their name as a full service provider in the field of screwdriving automation. Their core competencies include high quality EC servo screwdrivers and EC screwdrivers, sophisticated measurement technology and first class screw feeders which make them a much sought-after partner in the field of automated assembly.

Press Contact:

Dagmar Dübbelde
Carl-Schulz-Platz 1
D-92224 Amberg
Tel: 09621 371-343
Fax: 09621 371-199

Copyrighted images:

Please pay attention to our legal notice. Some images are copyrighted by third parties. Any use without specifying the source or modification for use in any other purpose is prohibited.